Sikkerhedsregler ved el-svejsning
Når der elsvejses, skal der beskyttes imod el, bestråling m.v.
Vekselstrømssvejsemaskiner skal være monteret med tomgangsregulator, hvis man er i berøring med emnet.
Husk derfor at:
-
Anvende svejsehjelm eller håndskærm der dækker hals samt den hånd, der holder skærmen.
-
Jordforbindelse i svejsestrømkreds skal være forbundet til arbejdsstykket.
-
Bygningsdele, rør, ledninger etc. må ikke indgå som leder.
-
Når en elektrode sættes i, må den kun berøres med isolerende handsker.
-
At svejsehandsker skal være hele og tørre.
-
Ikke at bære kablet over nakke eller skuldre, da et svejsekabel kan have en beskadiget isolation, der ikke umiddelbart kan ses.
-
Defekt svejseudstyr anmeldes straks til arbejdslederen.
-
Anvend særligt svejseudstyr under montage og reparationssvejsning i våde omgivelser, eller hvor svejseren står eller sidder på arbejdsstykket.
-
Svejsemaskinerne skal slukkes ved arbejdstidens ophør.
FH Contractors' retningslinjer udgør minimumsstandarder for sikkerhedsregler, med mindre skriftlig besked om andet gives. Lokale sikkerhedskrav fra andre virksomheder, som vedrører dit arbejde, skal prioriteres over FH Contractors' retningslinjer.
Du skal altid overholde lovgivningen i det land, hvor du arbejder. Overtrædelse kan medføre hjemsendelse.
På arbejdspladsen er alkohol og euforiserende stoffer forbudt, ligesom beruselse eller påvirkning ikke tolereres. Misbrug vil medføre øjeblikkelig bortvisning for din egen regning.
Husk, sikkerhed kommer altid i første række!
Disse retningslinjer udgør fundamentet for sundhed, miljø, sikkerhed og kvalitet hos FH Contractors. Ved at efterleve dem bidrager du til vores fælles mål om at opretholde et højt sikkerhedsniveau på arbejdspladsen, hvilket beskytter både mennesker, miljø og materiel.
9 Life Saving Rules
Bypassing Safety Controls
Obtain authorisation before overriding or disabling safety-controls:
-
I understand and use safety-critical equipment and procedures which apply to my task
-
I obtain authorisation before:
-
disabling or overriding safety equipment
-
deviating from procedures
-
crossing a barrier
-
Confined Space
Obtain authorisation before entering a confirned space:
-
I confirm energy sources are isolated
-
I confirm the atmosphere has been tested and is monitored
-
I check and use my breathing apparatus when required
-
I confirm there is an attendant standing by
-
I confirm a rescue plan is in place
-
I obtain authorisation to enter.
Safe Mechanical Lifting
Plan lifting operations and control the area:
-
I confirm that the equipment and load have been inspected and are fit for purpose
-
I only operate equipment that I am qualified to use
-
I establish and obey barriers and exclusion zones
-
I never walk under a suspended load.
Work Authorization
Work with a valid permit when required:
-
I have confirmed if a permit is required
-
I am authorised to perform the work
-
I understand the permit
-
I have confirmed that hazards are controlled and it is safe to start
-
I stop and reassess if conditions change.
Driving
Follow safe driving rules:
-
I always wear a seatbelt
-
I do not exceed the speed limit, and reduce my speed for road conditions
-
I do not use phones or operate devices while driving
-
I am fit, rested and fully alert while driving
-
I follow journey management requirements.
Hot Work
Control flammables and ignition sources:
-
I identify and control ignition sources
-
Before starting any hot work:
-
I confirm flammable material has been removed or isolated
-
I obtain authorisation
-
-
Before starting hot work in a hazardous area I confirm:
-
a gas test has been completed
-
gas will be monitored continually.
-
Working at Height
Protect yourself against a fall when working at height:
-
I inspect my fall protection equipment before use
-
I secure tools and work materials to prevent dropped objects
-
I tie off 100% to approved anchor points while outside a protected area.
Energy isolation
Verify isolation and zero energy before work begins:
-
I have identified all energy sources
-
I confirm that hazardous energy sources have been isolated, locked, and tagged
-
I have checked there is zero energy and tested for residual or stored energy.
Line of fire
Verify isolation and zero energy before work begins:
-
I position myself to avoid:
-
moving objects
-
vehicles
-
pressure releases
-
dropped objects
-
-
I establish and obey barriers and exclusion zones
-
I take action to secure loose objects and report potential dropped objects