google-site-verification=N_Yqx9RjHE2kOk6P3YFc_GSDsv_91ndCrPdIe95GCIo
top of page
Industrial Construction Worker_edited.jpg

Arbeid i høyden > 2 meter

Life-Saving rules working at height

Retningslinjer for arbeid i høyden

  • Du skal ikke arbeide i høyden alene

  • Før du arbeider i høyder over 2m, skal det gjøres en sikkerhetsvurdering. Arbeidsleder er ansvarlig. Dette skal dokumenteres

  • Du skal bruke godkjent fallsikringssele med to kroker

  • Du skal ha dokumentert opplæring i bruk av sele

  • Når du bruker en krakk eller gardintrapp på stillads eller utvendige plattformer, og avstanden til rekkverket er mindre enn høyden på krakk / Stige, skal du bruke fallsikringssele

  • Fest fallsikringsselen så høyt som mulig for å redusere et eventuelt fall. Forankringspunktet må motstå en kraft på min. 1500 kg.

  • Sperr av området under arbeidsplassen hvis det er fare for fallende gjenstander (se mere om fallende gjenstander)

  • Sjekk at fallsikringssele har godkjent årlig sertifisering - tilsvarende som løfteutstyr.

Sikkerhedsregler ved arbejde i højder over 2 meter

Husk, sikkerhet kommer alltid først!

isse retningslinjene utgjør grunnlaget for helse, miljø, sikkerhet og kvalitet hos FH Contractors. Ved å følge dem bidrar du til vårt felles mål om å opprettholde et høyt sikkerhetsnivå på arbeidsplassen, noe som beskytter både mennesker, miljø og materiell.

9 Life Saving Rules

Life-Saving Rules FH Saftey Control

Bypassing Safety Controls

Obtain authorisation before overriding or disabling safety-controls:

  •  I understand and use safety-critical equipment and procedures which apply to my task

  • I obtain authorisation before:

    • disabling or overriding safety equipment

    • deviating from procedures

    • crossing a barrier

Life-Saving Rulle  Confined Space

Confined Space

Obtain authorisation before entering a confirned space:

  •  I confirm energy sources are isolated

  • I confirm the atmosphere has been tested and is monitored

  • I check and use my breathing apparatus when required

  • I confirm there is an attendant standing by

  • I confirm a rescue plan is in place

  • I obtain authorisation to enter.

Life-Saving rule Safe mechanical lifting

Safe Mechanical Lifting

Plan lifting operations and control the area:

  •  I confirm that the equipment and load have been inspected and are fit for purpose

  • I only operate equipment that I am qualified to use

  • I establish and obey barriers and exclusion zones

  • I never walk under a suspended load.

Life-Saving rule work authorisation

Work Authorization

Work with a valid permit when required:

  •  I have confirmed if a permit is required

  • I am authorised to perform the work

  • I understand the permit

  • I have confirmed that hazards are controlled and it is safe to start

  • I stop and reassess if conditions change.

Life-Saving rule  drive safe

Driving

Follow safe driving rules:

  •  I always wear a seatbelt

  • I do not exceed the speed limit, and reduce my speed for road conditions

  • I do not use phones or operate devices while driving

  • I am fit, rested and fully alert while driving

  • I follow journey management requirements.

Life-saving rule hot work

Hot Work

Control flammables and ignition sources:

  •  I identify and control ignition sources

  • Before starting any hot work:

    • I confirm flammable material has been removed or isolated

    • I obtain authorisation

  • Before starting hot work in a hazardous area I confirm:

    • a gas test has been completed

    • gas will be monitored continually.

Life-Saving rules working at height

Working at Height

Protect yourself against a fall when working at height:

  • I inspect my fall protection equipment before use

  • I secure tools and work materials to prevent dropped objects

  • I tie off 100% to approved anchor points while outside a protected area.

Life-Saving rule energy isolation

Energy isolation

Verify isolation and zero energy before work begins:

  •  I have identified all energy sources

  • I confirm that hazardous energy sources have been isolated, locked, and tagged

  • I have checked there is zero energy and tested for residual or stored energy.

Safety icon FH Conreactors

Line of fire

Verify isolation and zero energy before work begins:

  • I position myself to avoid:

    • moving objects

    • vehicles

    • pressure releases

    • dropped objects

  • I establish and obey barriers and exclusion zones

  • I take action to secure loose objects and report potential dropped objects

bottom of page